All Packages  Class Hierarchy  This Package  Previous  Next  Index

Class byucc.jhdl.Xilinx.Virtex.clkdll

java.lang.Object
   |
   +----byucc.jhdl.base.Nameable
           |
           +----byucc.jhdl.base.Node
                   |
                   +----byucc.jhdl.base.Cell
                           |
                           +----byucc.jhdl.base.Annotation
                                   |
                                   +----byucc.jhdl.Xilinx.Virtex.clkdll

public final class clkdll
extends Annotation
implements PreDefinedSchematic
CLKDLL is a clock delay locked loop used to minimize clock skew. CLKDLL synchronizes the clock signal at the feed back clock input (CLKFB) to the clock signal at the input clock (CLKIN). The locked output (LOCKED) is high when the two signals are in phase. The signals are considered to be in phase when their rising edges are within 250 ps of each other. The frequency of the clock signal at the CLKIN input must be in the range 25 - 90 MHz. The CLKIN pin must be driven by an IBUFG or a BUFG. On-chip synchronization is achieved by connecting the CLKFB input to a point on the global clock network driven by a BUFG, a global clock buffer. The BUFG input can only be connected to the CLK0 or CLK2X output of CLKDLL. The BUFG connected to the CLKFB input of the CLKDLL must be sourced from either the CLK0 or CLK2X outputs of the same CLKDLL. The CLKIN input should be connected to the output of an IBUFG, with the IBUFG input connected to a pad driven by the system clock. Off-chip synchronization is achieved by connecting the CLKFB input to the output of an IBUFG, with the IBUFG input connected to a pad. Either the CLK0 or CLK2X output can be used but not both. The CLK0 or CLK2X must be connected to the input of OBUF, an output buffer. The duty cycle of the CLK0 output is 50-50 unless the DUTY_CYCLE_CORRECTION attribute is set to FALSE, in which case the duty cycle is the same as that of the CLKIN input. The duty cycle of the phase shifted outputs (CLK90, CLK180, and CLK270) is the same as that of the CLK0 output. The duty cycle of the CLK2X and CLKDV outputs is always 50-50. The frequency of the CLKDV output is determined by the value assigned to the CLKDV_DIVIDE attribute. The master reset input (RST) resets CLKDLL to its initial (power-on) state. The signal at the RST input is synchronized to the clock signal at the CLKIN input. The reset becomes effective at the second Low-to-High transition of the clock signal at the CLKIN input after assertion of the RST signal. (Source: XACT Libraries Guide, Chapter 4 CLKDLL, Xilinx Corporation, 1999.)


Variable Index

 o cell_interface
The port interface for clkdll: clkin: in (1) clkfb: in (1) rst: in (1) clk0: out (1) clk90: out (1) clk180: out (1) clk270: out (1) clk2x: out (1) locked: out (1)
 o cellname
The static cellname (netlist reference name) for clkdll

Constructor Index

 o clkdll(Node)
Used only by child classes to pass up the parent cell.
 o clkdll(Node, ArgBlockList)
Constructs a new clkdll, connecting its ports as given by the String-Wire pairs in the ArgBlockList.
 o clkdll(Node, String)
Used only by child classes to pass up the parent cell and instance name.
 o clkdll(Node, String, ArgBlockList)
Constructs a new clkdll, connecting its ports as given by the String-Wire pairs in the ArgBlockList, with the initial String parameter as the instance name.
 o clkdll(Node, String, String, Wire, String, Wire, String, Wire, String, Wire, String, Wire, String, Wire, String, Wire, String, Wire, String, Wire)
Constructs a new clkdll, connecting each Wire to the port whose name is given by the accompanying String parameter, with the initial String parameter as the instance name.
 o clkdll(Node, String, Wire, String, Wire, String, Wire, String, Wire, String, Wire, String, Wire, String, Wire, String, Wire, String, Wire)
Constructs a new clkdll, connecting each Wire to the port whose name is given by the accompanying String parameter.
 o clkdll(Node, String, Wire, Wire, Wire, Wire, Wire, Wire, Wire, Wire, Wire)
Constructs a new clkdll, with the initial String parameter as the instance name.
 o clkdll(Node, Wire, Wire, Wire, Wire, Wire, Wire, Wire, Wire, Wire)
Constructs a new clkdll.

Method Index

 o cellInterfaceDeterminesUniqueNetlistStructure()
 o main(String[])
 o test()
 o type()

Variables

 o cellname
 public static final String cellname
The static cellname (netlist reference name) for clkdll

 o cell_interface
 public static CellInterface cell_interface[]
The port interface for clkdll: clkin: in (1) clkfb: in (1) rst: in (1) clk0: out (1) clk90: out (1) clk180: out (1) clk270: out (1) clk2x: out (1) locked: out (1)

Constructors

 o clkdll
 protected clkdll(Node parent)
Used only by child classes to pass up the parent cell.

Parameters:
parent - Parent cell
 o clkdll
 protected clkdll(Node parent,
                  String name)
Used only by child classes to pass up the parent cell and instance name.

Parameters:
parent - Parent cell
name - Instance name of the cell
 o clkdll
 public clkdll(Node parent,
               Wire clkin,
               Wire clkfb,
               Wire rst,
               Wire clk0,
               Wire clk90,
               Wire clk180,
               Wire clk270,
               Wire clk2x,
               Wire locked)
Constructs a new clkdll.

Parameters:
parent - The parent Cell to the clkdll
clkin - The Wire to be connected to input port clkin
clkfb - The Wire to be connected to input port clkfb
rst - The Wire to be connected to input port rst
clk0 - The Wire to be connected to output port clk0
clk90 - The Wire to be connected to output port clk90
clk180 - The Wire to be connected to output port clk180
clk270 - The Wire to be connected to output port clk270
clk2x - The Wire to be connected to output port clk2x
locked - The Wire to be connected to output port locked
 o clkdll
 public clkdll(Node parent,
               String instanceName,
               Wire clkin,
               Wire clkfb,
               Wire rst,
               Wire clk0,
               Wire clk90,
               Wire clk180,
               Wire clk270,
               Wire clk2x,
               Wire locked)
Constructs a new clkdll, with the initial String parameter as the instance name.

Parameters:
parent - The parent Cell to the clkdll
instanceName - The instance name of the clkdll
clkin - The Wire to be connected to input port clkin
clkfb - The Wire to be connected to input port clkfb
rst - The Wire to be connected to input port rst
clk0 - The Wire to be connected to output port clk0
clk90 - The Wire to be connected to output port clk90
clk180 - The Wire to be connected to output port clk180
clk270 - The Wire to be connected to output port clk270
clk2x - The Wire to be connected to output port clk2x
locked - The Wire to be connected to output port locked
 o clkdll
 public clkdll(Node parent,
               String s0,
               Wire w0,
               String s1,
               Wire w1,
               String s2,
               Wire w2,
               String s3,
               Wire w3,
               String s4,
               Wire w4,
               String s5,
               Wire w5,
               String s6,
               Wire w6,
               String s7,
               Wire w7,
               String s8,
               Wire w8)
Constructs a new clkdll, connecting each Wire to the port whose name is given by the accompanying String parameter.

Parameters:
parent - The parent Cell to the clkdll
s0 - The name of the port to which w0 will be connected
w0 - The Wire to be connected to the port specified by s0
s1 - The name of the port to which w1 will be connected
w1 - The Wire to be connected to the port specified by s1
s2 - The name of the port to which w2 will be connected
w2 - The Wire to be connected to the port specified by s2
s3 - The name of the port to which w3 will be connected
w3 - The Wire to be connected to the port specified by s3
s4 - The name of the port to which w4 will be connected
w4 - The Wire to be connected to the port specified by s4
s5 - The name of the port to which w5 will be connected
w5 - The Wire to be connected to the port specified by s5
s6 - The name of the port to which w6 will be connected
w6 - The Wire to be connected to the port specified by s6
s7 - The name of the port to which w7 will be connected
w7 - The Wire to be connected to the port specified by s7
s8 - The name of the port to which w8 will be connected
w8 - The Wire to be connected to the port specified by s8
 o clkdll
 public clkdll(Node parent,
               String instanceName,
               String s0,
               Wire w0,
               String s1,
               Wire w1,
               String s2,
               Wire w2,
               String s3,
               Wire w3,
               String s4,
               Wire w4,
               String s5,
               Wire w5,
               String s6,
               Wire w6,
               String s7,
               Wire w7,
               String s8,
               Wire w8)
Constructs a new clkdll, connecting each Wire to the port whose name is given by the accompanying String parameter, with the initial String parameter as the instance name.

Parameters:
parent - The parent Cell to the clkdll
instanceName - The instance name of the clkdll
s0 - The name of the port to which w0 will be connected
w0 - The Wire to be connected to the port specified by s0
s1 - The name of the port to which w1 will be connected
w1 - The Wire to be connected to the port specified by s1
s2 - The name of the port to which w2 will be connected
w2 - The Wire to be connected to the port specified by s2
s3 - The name of the port to which w3 will be connected
w3 - The Wire to be connected to the port specified by s3
s4 - The name of the port to which w4 will be connected
w4 - The Wire to be connected to the port specified by s4
s5 - The name of the port to which w5 will be connected
w5 - The Wire to be connected to the port specified by s5
s6 - The name of the port to which w6 will be connected
w6 - The Wire to be connected to the port specified by s6
s7 - The name of the port to which w7 will be connected
w7 - The Wire to be connected to the port specified by s7
s8 - The name of the port to which w8 will be connected
w8 - The Wire to be connected to the port specified by s8
 o clkdll
 public clkdll(Node parent,
               ArgBlockList abl)
Constructs a new clkdll, connecting its ports as given by the String-Wire pairs in the ArgBlockList. Any generic assignments are made through String-String pairs in the ArgBlockList.

Parameters:
parent - The parent Cell to the clkdll
abl - The list of String-Wire pairs for port assignments, and String-String pairs for generic assignments.
 o clkdll
 public clkdll(Node parent,
               String instanceName,
               ArgBlockList abl)
Constructs a new clkdll, connecting its ports as given by the String-Wire pairs in the ArgBlockList, with the initial String parameter as the instance name. Any generic assignments are made through String-String pairs in the ArgBlockList.

Parameters:
parent - The parent Cell to the clkdll
instanceName - The instance name of the clkdll
abl - The list of String-Wire pairs for port assignments, and String-String pairs for generic assignments.

Methods

 o cellInterfaceDeterminesUniqueNetlistStructure
 public final boolean cellInterfaceDeterminesUniqueNetlistStructure()
Overrides:
cellInterfaceDeterminesUniqueNetlistStructure in class Cell
 o type
 public int type()
 o main
 public static void main(String argv[])
 o test
 public static void test()

All Packages  Class Hierarchy  This Package  Previous  Next  Index